Help with Z-Axis Problem needed
@Signdude wrote: I've done a search on the forum for Z-Axis and found many related posts.with symptoms similar to mine. I see there is a post dated yesterday with the topic "Removing a Z-axis spring"....
View ArticleClik here to view.
Is this the correct nut to adjust the slack out of the zx carrier?
@Mont wrote: I have a bit of slack in my setup and I don't think tightening this particular nut is mentioned in the assembly instructions. I keep getting small edges that are rough and on the entire...
View ArticleNew Build of XXL
@Biologyben wrote: Just finished a new build of an XXL following directions provided by Carbide 3D. I estimate it took twice as long as needed due to some issues with the directions provided/lack of...
View ArticleConnectors by homing switches
@relic wrote: Are the extra connectors in the row where the homing switches connect functional, or for later use. I can't seem to find a schematic or pinout for the controller board. Posts: 5...
View ArticleIssues on Touch Screen
@Biologyben wrote: So I understand that Motion 4 is in BETA now, and I'm using 3 as I've just got the machine up and running. That said, I was hoping to use Motion with a touch screen interface only...
View ArticleEngraving logos
@ronron wrote: I AM INTERESTED IN PURCHASING A NOMAD 883.However,I would like to know how fine a line I can it engrave.Thanks Posts: 2 Participants: 2 Read full topic
View ArticleLaser engraving
@ronron wrote: Does anyone know if the nomad 883 can be turbed into a laser engraver?Thanks Posts: 1 Participants: 1 Read full topic
View ArticleThis app can't run on your PC
@darkwingduck wrote: HI @all, I tried to run CarbideUpdater on my Win10 tablet. After start-up, I'm getting the following error message:"This app can't run on your PC" Maybe some missing runtimes?Any...
View ArticleS03 XL, My Y Axis is off by almost ~2.5mm
@irr1449 wrote: I have been machine some fairly soft 3/4 inch pine boards and I noticed that my Y axis is cutting short by about 2-3mm every time. My X axis is accurate to a faction of a mm (even on a...
View ArticleMonitor job progress remotely
@tito wrote: I know, I know--"never leave your mill unattended when it's running." That's great advice and you should always follow it. However, if you're going to disregard that for brief periods and...
View ArticleClik here to view.
How to define a roundover bit in Carbide Create
@Zoomer wrote: How can I define a roundover bit for edge finishing in Carbide Create Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Another round of keychains
@ItsDan wrote: Photo Mar 04, 3 35 40 PM.jpg3264x2448 1.68 MB This is actually the first non-"one off" project I've done on my Shapeoko, I'd precut the blanks using traditional woodworking tools so I...
View ArticleClik here to view.
Maximal material thickness
@bitterandreal wrote: Hi, I want to buy a Shapeoko XL but I need to work with some 3 1/2 inch thick materials.What is the maximal material thickness on the Shapeoko XL? S3300-XL-FRONT.jpg1108x575 59.4...
View ArticlePoorman's enclosure 36 decibel reduction
@grumpa wrote: I wanted a window in the door. I was advised by my esteemed college to have a solid door since I have a camera inside. I listened and learned and SUCCEEDED ! Using a decibel meter I...
View ArticleMaximum Material Width?
@taylorbevis wrote: For the standard Shapeoko 3, I see that the max cutting area is 16x16. But what is the widest piece of stock that will fit without obstructing gantry motion? Posts: 1 Participants:...
View ArticleEllipses, can't do that simple thing now
@DJ_Valenski wrote: How about making an oval or ellipse? Posts: 3 Participants: 2 Read full topic
View ArticlePlunge cut a 1/8 hole?
@DJ_Valenski wrote: Using 1/8 bit, how do I simply plunge down to make a 1/8" hole? (In Carbide Create) Posts: 3 Participants: 3 Read full topic
View ArticleRouter Runout - Cuts at an Angle
@Bonch wrote: I tested the runout on my router and found it to be .011" out. I purchased some PreciseBits collets to see if that would remove it. It didnt. I spent most of this afternoon trying to...
View ArticleClik here to view.
SuperPID Build complete
@Hcomet wrote: Ordered a SuperPID back in September when they had their sale but I only got around to building a case and installing it in late January. Well started in January, but I'm finally...
View ArticleCarbide Create G-CODE
@plundh wrote: Hi all creators- Line 12 (Bold and Italics) in my G-Code generated with Carbide Create for Nomad883 contains 'A0.000', which makes Z-homing incredibly slow (see below). Is there a...
View Article